Installation Instructions

Single Entry Door System

4/3/2010

Dorplex Industries Limited

Emidio Salvi 

 

Click here to download Installation Instructions Document

Upon receipt of your Dorplex door system it is imperative that you unwrap and inspect it to ensure that it is free of manufacturers’ defects, not damaged and is as ordered.  Please take the time to measure to verify sizing.  It is best that this be conducted at time of delivery not at installation.  Any damages or deficiencies MUST be reported immediately and you are not to continue with installation.

Listed below are the steps necessary to properly install a door system.  It is not an all inclusive list and is recommended that it be uses as a guideline only.

1. Preparation of rough opening

 

• Make sure the opening in which the Dorplex door system is being installed is a minimum of 1” larger in width and ½” larger in height.  This will allow for adjustment when squaring and shimming the system in place.
• Verify that the rough opening is plumb, square and level.
• Clean and dry the sub floor area.

 

2. Caulk the sub floor

 

• Next ensure that the sill sub floor is solid and level and apply two or more beads of sealant.  This will reduce movement, lift and reduce the risk of water penetrating between the sub floor and the new Dorplex door system.  The rows of sealant should be about 1” apart and start about 1” from the inside edge.
• In the event that there is a large gap between the sill and the sub floor it might be necessary for you to use low expansion foam.  This foam will help to insulate the system and will also assist in the reduction of movement.

 

 

3. Door placement

 

• Place the new door system into the opening with the door in the closed position.  If you are not a professional installer it is recommended that you do not try this alone.  You are to place the sill in the opening first and then tilt the door up into the opening.

 

 

4. Plumb and fasten the door

 

• Firmly place shims between the opening and the door system frame at the bottom (at sill) and at header in all four corners.  You may have to adjust the shims in order to get the door system square and level in place.  One way to ensure that the system is level and square is to close the door and visually inspect to see if it makes contact with the weather stripping evenly on the lock side of the door from top to bottom.
• Next shim behind each hinge at the jamb and place shims on the opposite side of the frame parallel to the hinges.  This will allow you to adjust the gap around the door to reflect approximately 1/8” gap all around.
• It is recommended that you place a 3” screw at each set of shims (total of 6 sets) through the frame.  Make sure all screws penetrate the shims and reach the stud to prevent the frame from warping.  On prefinished systems you can affix the screws behind the weather stripping so they are not visible.  In addition you can pre-drill 3 holes on the opposite side in which to install the installation screws.  In order to ensure the screws are not visible cover them with vinyl screw covers.
• Test operation of the door system making sure that it performs properly.
• You will be provided with three screws that you are required to install.  Placement of these screws is very important.  You must remove one of the center screws in each hinge and install the screws provided.  This will reduce the amount of sag or drift that may occur over time.  These screws must also penetrate the shims and reach the stud.

 

 

5. Finishing touches

 

• Install dead bolt and striker plates at the correct location.
• Insulate around the door between the jamb and the wall studs.  Please note it is important to use  ONLY low expansion foam.  If you do not use low expansion foam then the door jamb will warp.
• Caulk around the doorway including the front sill edge and along the exterior where it meets the brick or siding.
• Adjust sweep, remove vinyl strip cover (slide cover toward the open side).  Push sweep down ward to make sure the fins make contact with the sill or until light is no longer visible.  Tighten screws and replace the vinyl strip cover.
• Once installation is complete visibly inspect all joints to ensure the factory applied caulking has not cracked during installation.  If any cracks found the caulking should be reapplied to prevent water from entering the home.

Attached you will find a series of pictures that may assist in explaining the information provided above.